Page 3 of 3
Re: AusBonsai Market - Sunday 11th March 2018 - Sydney
Posted: March 11th, 2018, 7:58 pm
by kachmica
GREAT DAY !!!!!
Both Goulburn "wagons" were as full as googs going home.
Exceptional array of Bonsai goodies at really good prices (which I purchased my fair share) and met some long-time Bonsai friends who we only see occasionally now.
Not only a great sales event but a great Bonsai community get-together.
Well done to Steven and his helpers.
Re: AusBonsai Market - Sunday 11th March 2018 - Sydney
Posted: March 12th, 2018, 2:21 pm
by Bougy Fan
A photo not long after the crowd flooded in Sunday morning
DSC_4850-2.jpg
and another
DSC_4856.jpg
Re: AusBonsai Market - Sunday 11th March 2018 - Sydney
Posted: March 12th, 2018, 8:32 pm
by Sno
Thanks Ausbonsai for putting on a great day . I think it gets better each year .i was not going to bring anything home but I ended up with a beautiful PK pot . Oh and a couple more trees .
Re: AusBonsai Market - Sunday 11th March 2018 - Sydney
Posted: March 13th, 2018, 10:24 am
by hugh grant
Thanks to Steven for holding this market again, and thank you to all whom supported all the sellers and myself at the ‘Hugh Grant Design’ stall!! It was close to a sell out for me so thankyou all for your purchases!
I really Believe this event could easily be at least a 6 monthly market. Something to consider I think!
Re: AusBonsai Market - Sunday 11th March 2018 - Sydney
Posted: August 12th, 2020, 12:11 am
by WMC
sreeve wrote: ↑March 7th, 2018, 12:07 pm
WIRE CADDY
Several bonsai wire roll caddy’s will be available for purchase at $130 each. These units are a great accessory:
- - Hold 6 off 0.5kg or 1kg rolls.
- Each spool rotates freely and independent of axle.
- Easily replace a complete roll of wire as shown in the progressive photographs (WITHOUT winding the wire onto the spool).
- Perfect accessory to prevent wire “nests” and easy access to wire.
- Typically used with wire sizes of diameter 1.0mm, 1.5mm, 2.0mm, 2.5mm, 3.0mm & 3.5mm
- Spools are completely assembled – ready to use.
This version has several improvements over its predecessor in that no tools are required to fit or replace complete wire rolls.
Caddy.jpg
NOTE:
1. Wire not included
2. Colour of side frame is white (not black as shown in the above earlier models)
An instruction sheet including more details is attached below
Bonsai wire caddy_1 March 2018_a.pdf
Just wondering if anyone can point me in the direction of the spools shown in this Wire Caddy? Looking to make one and cant find the right size anywhere. I'm in Melbourne FYI.
Thanks in advance
Re: AusBonsai Market - Sunday 11th March 2018 - Sydney
Posted: August 12th, 2020, 11:21 am
by KIRKY
If your planning on making one, you make it to the size you want it. There would be A lot of youtube DIY if your wanting ideas.
Cheers
Kirky
Re: AusBonsai Market - Sunday 11th March 2018 - Sydney
Posted: August 12th, 2020, 12:04 pm
by Keels
WMC wrote: ↑August 12th, 2020, 12:11 am
..... point me in the direction of the spools shown in this Wire Caddy? Looking to make one and cant find the right size anywhere. I'm in Melbourne FYI.
Thanks in advance
If you google " Empty 3d printer spool" or "Empty filament spool" you will find a couple of options.
These guys seem to have a range of good sizes you might find handy
http://www.crownplastics.com.au/produc ... small.html