AusBonsai

This tree looks amazing.....very inspiring thank you.

Mate this one has always been one of my favorites out of all the pines I've seen.

Absolutely love it.

Thanks for keeping us updated!

Mo


Sent from my iPhone using Tapatalk

hi everyone,
just going through the japanese black pines today and i'd share a bit of progress and what's being done to them.
the first one had all the large branches replaced with closer back buds, which are wired into position. the needles are a bit long due to being left to grow for one season. the reverse taper in the lower trunk is improving since 4 wedges were banged into the thinner section to force thickening. it measures 35cm in height. here is another one, the result will be revealed tomorrow.
regards

well, here it is after wiring. it measures at 26cm in height. this one has rather impressive nebari. here is another one done today. it measured at 35cm in height. a bit of reverse taper just above the nebari. it was split and inserted with two plastic wedges to thicken it.
regards

Top work as always mate, look forward to seeing these develop in the future.

Cheers,
Mo

bonsaisensation wrote: it was split and inserted with two plastic wedges to thicken it.

Hi There,

Thanks for taking the time to post these. Can you give us a little more info on this method and how you do it?

regards
Drew

hi Drew
i used a trunk splitter to make two incisions into the part of the trunk that is thinner and needs to thicken. i then inserted and hammered in a plastic wedge used in spacing tiles to push the gap wider. the gap is then sealed up with cutting paste. as the tree grows over the next season, the "purposely wounded" part will grow thicker as the tree tries to heal the wound.
this method is nothing new and we have used it to great effect with cedars and pines to create taper and correct reverse taper. i'll update with some photos next time we do it.


regards


Tien

So when you use the trunk splitters, do you split the trunk all the way down to the roots or just the the section of trunk you want to thicken? I guess depending on the tree you could do either successfully right? Photos would be great if you have any.

Thanks for posting!

hi Drew
here it goes: the wedges will stay in the trunk and i shall report in a couple of year to update its progress.
note that there are some existing wedges in the trunk. they were put in there last year. due to the tree was not fed a lot this year, it did not grow enough to callus. but it has worked on quite a number of trees and i have no doubt it will with this tree.

regards

Tien

Hi Tien,
Some great pines there and excellent work. The wedges work well. Some good info. Thanks for posting these
Andrew

Maybe the mods can separate the wedge technique into its own thread as well?

Some great shots there, and something I think we can all use on pines with this issue.

Thanks for sharing

bonsaisensation wrote:an update on the bunjin black pine

DSCN0449a.jpg

DSCN0451a.jpg

the long hanging branch had been jinned as it was adding too much volumn and weight to the foliage. the rest of the branches have all been cut back to better back buds to form a more compact branch structure. it doesn't show all that well in the photo behind all the needles, but the short left branch is my favourite branch having good movement and short internodes.



regards

To continue watching this tree develop visit viewtopic.php?f=131&t=24423

bonsaisensation wrote:well, here it is after wiring. it measures at 26cm in height. this one has rather impressive nebari.

IMG_1360a.jpg

here is another one done today. it measured at 35cm in height. a bit of reverse taper just above the nebari. it was split and inserted with two plastic wedges to thicken it.

IMG_1361a.jpg

IMG_1362a.jpg

regards

To continue to watch the first tree develop visit: viewtopic.php?f=131&t=24426


to continue to watch the second tree develop visit: viewtopic.php?f=131&t=24427

bonsaisensation wrote:hi everyone,
just going through the japanese black pines today and i'd share a bit of progress and what's being done to them.
the first one had all the large branches replaced with closer back buds, which are wired into position. the needles are a bit long due to being left to grow for one season. the reverse taper in the lower trunk is improving since 4 wedges were banged into the thinner section to force thickening. it measures 35cm in height.

IMG_1354a.jpg

IMG_1355a.jpg

here is another one, the result will be revealed tomorrow.

IMG_1356a.jpg

regards

to continue to watch this tree progress visit: viewtopic.php?f=131&t=24428


thank you Tien for producing some phenomenal trees!

bunce.