Here is my entry into the Literati, new stock competition. It is a Juniper Chinensis 'Robusta Green' . Cost $12.00
I chose this tree because it has already got some movement in the lower trunk and has lots of branches to chose from. I was 800mm high , the trunk thickness ranges from 30mm at the base to 20mm 3/4 of the way up the tree. This is the very first time I have ever wrapped a tree to bend and I have no experience with this style at all. At this stage I have left quite a lot of foliage on the tree.
I used wet cotton binding tape to wrap the tree and 4 x 2.5mm galv wire rods for support. Everything seemed to go well, though I am not sure if this is the correct procedure. Worked for me so I am happy. How long do I need to leave it wrapped and supported by the wire rods ?
New entry - Juniper Chinensis
Moderator: Bretts
- Terry
- Aussie Bonsai Fan
- Posts: 94
- Joined: June 12th, 2009, 10:09 am
- Favorite Species: All
- Bonsai Age: 5
- Bonsai Club: Newcastle
- Location: Newcastle Area
- Has thanked: 19 times
- Been thanked: 23 times
New entry - Juniper Chinensis
You do not have the required permissions to view the files attached to this post.
- Pup
- Knowledgeable rogue
- Posts: 6357
- Joined: November 12th, 2008, 5:19 pm
- Favorite Species: melaleucas
- Bonsai Age: 31
- Bonsai Club: Bonsai society of Western Australia
- Location: Southern Suburbs of Perth Western Australia
- Been thanked: 36 times
- Contact:
Re: New entry - Juniper Chinensis
If it worked for you then that is all that matter's. You have also pasted this information on which is even better.
As for how long you leave it on
How long is a piece of string watch for it biting in to the trunk and branches.
Good start
cheers
Pup
As for how long you leave it on

Good start
cheers

IN THE LIGHT OF KNOWLEDGE ATTAINED, ACHIEVEMENT IS WITHIN SIGHT
I am not a complete fool, some parts are missing
I am not a complete fool, some parts are missing
- bodhidharma
- Aussie Bonsai Fan
- Posts: 5007
- Joined: August 13th, 2009, 1:14 pm
- Favorite Species: English Elm
- Bonsai Age: 24
- Bonsai Club: goldfields
- Location: Daylesford, Victoria....Central Highlands
- Been thanked: 11 times
- Contact:
Re: New entry - Juniper Chinensis
Hey Bustadog, you will need to leave it on for 3 months at least, checking all the time for the wire cutting into the bark. I probably would say you will have to do this process once or twice more to have success. Nice start.
"Advice is rarely welcome, and the one's who need it the most welcome it the least"
- Jamie
- Bonsai passionardo
- Posts: 6829
- Joined: August 21st, 2009, 8:08 pm
- Favorite Species: CLERO!!!,ficus, celtis, juniper, elms
- Bonsai Age: 9
- Bonsai Club: AUSBONSAI.COM
- Location: queensland, Hervey Bay
- Been thanked: 2 times
- Contact:
Re: New entry - Juniper Chinensis
busta,
just a little tip, be very cautious of using galv wire on your trees, even though they are galvanised they will still rust under constant moist conditions, this can cause some problems for your tree, one if left long enough will be death
just letting a know about the problems with gal wire
hope it helps.
jamie
just a little tip, be very cautious of using galv wire on your trees, even though they are galvanised they will still rust under constant moist conditions, this can cause some problems for your tree, one if left long enough will be death



jamie

SHOHIN YAKUZA!!!
taking the top half of trees of since 2005! 
and growing trees for the future generations! 50+ year plans


and growing trees for the future generations! 50+ year plans

- Pup
- Knowledgeable rogue
- Posts: 6357
- Joined: November 12th, 2008, 5:19 pm
- Favorite Species: melaleucas
- Bonsai Age: 31
- Bonsai Club: Bonsai society of Western Australia
- Location: Southern Suburbs of Perth Western Australia
- Been thanked: 36 times
- Contact:
Re: New entry - Juniper Chinensis
G,day Jamie has warned you of Galvanised wire, it is in certain circumstances very dangerous. Yes it can kill a conifer.
The biggest problem is when it contacts the cambium layer, of broken as in cracked or drilled or screws or nails though it. As yours is wrapped in cotton as in raffia type wrapping it should not be a big problem. Just watch the tree carefully as it puts on new growth.
Cheers
Pup
The biggest problem is when it contacts the cambium layer, of broken as in cracked or drilled or screws or nails though it. As yours is wrapped in cotton as in raffia type wrapping it should not be a big problem. Just watch the tree carefully as it puts on new growth.
Cheers

IN THE LIGHT OF KNOWLEDGE ATTAINED, ACHIEVEMENT IS WITHIN SIGHT
I am not a complete fool, some parts are missing
I am not a complete fool, some parts are missing
- Terry
- Aussie Bonsai Fan
- Posts: 94
- Joined: June 12th, 2009, 10:09 am
- Favorite Species: All
- Bonsai Age: 5
- Bonsai Club: Newcastle
- Location: Newcastle Area
- Has thanked: 19 times
- Been thanked: 23 times
Re: New entry - Juniper Chinensis
Thanks for the tips guys. You are correct pup, the tree has been wrapped twice with cotton binding tape, and the wire does not contact the tree / bark etc. I will keep a close watch on the wire and the tree and report any deterioration.